CAS DL-60 Specifications Page 69
- Page / 98
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Setup
CAS User’s Guide 59
Alarm Delay
You can set the CAS to delay normal alarm detection and alarm
reporting. There are two kinds of alarm delay:
•
Startup alarm delay delays detection of process alarms (but not failed
sensor alarms) for all channels for a time period you set in the Setup
Global Parameters main menu.
•
Channel alarm delay delays failed sensor alarms and process alarms
for one channel until the alarm condition is continuously present for
longer than the channel alarm delay time you set.
NOTE
Failed sensor alarms are detected at startup. They are affected by
the channel alarm delay, not the startup alarm delay time.
High Process Alarm Setpoint
This menu lets you select the setpoint (temperature or other value within
the scaled sensor range) at which the high process alarm activates. The
high process alarm activates when the process variable (PV) goes above
the high process setpoint. It deactivates when the PV goes below the
high process setpoint minus the deadband value, if you have set a
deadband value.
Selectable values: Any point within the scaled sensor range
High Process Alarm Type
This menu lets you turn off the high process alarm or set it to one of the
alarm functions. (See the previous description for an explanation of
these choices).
Selectable values: Off, Latched, Unlatched
CHANNEL PROCESS UNITS
CHANNEL NAME ALARM STATUS
01 HI PROC ALARM
SETPT ? 1000
°
F
CHANNEL PROCESS UNITS
CHANNEL NAME ALARM STATUS
01 HI PROC ALARM
TYPE ? OFF
- User ’s Guide 1
- Warranty 2
- Contents 3
- CAS User’s Guide iii 5
- Overview 7
- System Diagram 8
- Parts List 8
- 10
- Introduction 11
- Specifications 13
- Digital Inputs 14
- Digital Outputs 14
- System Digital Outputs 14
- Miscellaneous Specifications 15
- 6 CAS User’s Guide 16
- Installation 17
- Precautions and Warnings 18
- Recommended Tools 19
- CAS Mounting Procedure 20
- TB-50 Mounting Instructions 21
- Grounding 24
- Thermocouple Wiring 24
- Input Wiring 24
- Communications Wiring 25
- Wiring: Noise Suppression 26
- General Wiring 27
- Connections Test 28
- Wiring Outputs 29
- Using the Cable Tie Wraps 30
- Alarm Output Connections 31
- Watchdog Timer 31
- TB-50 Connections 32
- Input Scaling 33
- Scaling Values 34
- Scaling and Calibration 35
- T/C Inputs 36
- Connecting Thermocouples 36
- Current Inputs 36
- Voltage Inputs 37
- Unused Inputs 37
- Serial Communications 38
- JU 1JU 1 39
- Configuring Communications 40
- Recommended Wire Gauges 41
- 32 CAS User’s Guide 42
- Using the CAS 43
- Front Panel 44
- Single Channel Display 46
- Job Display 47
- Change Setpoint 48
- Acknowledging an Alarm 49
- Resetting an Alarm 49
- 40 CAS User’s Guide 50
- How to Enter the Setup Menus 51
- How to Edit a Menu 51
- CAS Menus 52
- Setup Global Parameters Menu 53
- Save Setup to Job 54
- Job Select Inputs 54
- Job Select Input Polarity 55
- Startup Alarm Delay 55
- Keyboard Lock Status 56
- Scanner Address 56
- Communications Error Checking 56
- Communications Baud Rate 57
- Allen-Bradley Protocol 57
- AC Line Frequency 57
- Digital Output Polarity 58
- EPROM Information 58
- Setup Channel Inputs 59
- Pulse Sample Time 60
- Channel Name 60
- Input Units 61
- Input Reading Offset 61
- Linear Scaling Menus 62
- Variable 63
- InputR eading 63
- Display Format 64
- High Process Value 64
- High Reading 65
- Low Process Value 65
- Low Reading 66
- Input Filter 66
- Setup Channel Alarms 67
- Alarm Delay 69
- High Process Alarm Setpoint 69
- High Process Alarm Type 69
- Deviation Alarm Value 70
- High Deviation Alarm Type 70
- Low Deviation Alarm Type 71
- Low Process Alarm Setpoint 72
- Low Process Alarm Type 72
- Alarm Deadband 73
- Manual I/O Test 75
- Digital Output Test 76
- Keypad Test 76
- Troubleshooting 77
- Manual System Reset 78
- Returning the Unit 78
- TB-50 Test 79
- Checking an Analog Input 79
- Checking Digital I/O 79
- Digital Input Test 80
- Computer Problems 81
- Ground Loops 82
- Software Problems 82
- User-Written Software 82
- Changing the EPROM 83
- Appendix: Linear Scaling 85
- Examples 85
- Example 2 86
- Example 3 87
- 78 CAS User’s Guide 88
- Glossary 89
- 88 CAS User’s Guide 98
Related products and manuals for Kitchen scales CAS DL-60
Kitchen scales CAS NC-100 User Manual
(48 pages)
(48 pages)
Kitchen scales CAS LP-II User Manual
(6 pages)
(6 pages)
Kitchen scales CAS Poscale User Manual
(104 pages)
(104 pages)
Kitchen scales CAS Sc Series Owner's Manual
(16 pages)
(16 pages)
Kitchen scales CAS DL-60 User Manual
(23 pages)
(23 pages)
Kitchen scales CAS LP-II User Manual
(59 pages)
(59 pages)
© 2020, manymanuals.com. All rights reserved. | 0.263 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals